 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Broadcast Quality (560 Series) 1 5 P.C. BOARD MOUNT - EPOXY POTTED AUDIO TRANSFORMERS * Rugged black epoxy potted case with 9 pin connections (.025" square by 0.5" long). * Frequency response @ 0 dbm +/- 1 db max. (+/- 0.5 db is typical) of 30 Hz. to 30 Khz., except 560Q which is 30 Hz. to 15 Khz. * Insertion loss of 1 db max. * Maximum power level 0 dbm. * Electrostatic shield between primary & secondary connected to core and pin "SH". * Humbucking construction * Balanced split windings on primary & secondary for circuit versatility. * Primaries and secondaries can be reversed for impedance matching. * Overall dimensions 1.64" x 1.33" x 0.85" high max. * Shipping weight 4 oz. Part No. 560C 560E 560G 560J 560L 560N 560Q Application Emitter or mic to Line Emitter or mic to Line Isolating or Hybrid Collector to Line or Line to Base Collector to Line or Matching Collector to Line Matching or Bridging Nominal Impedance Primary Secondary 12/48 150/600 50/200 150/600 150/600 150/600 150/600 1200/4800 150/600 5K/20K 150/600 10K/40K 10k/40k 10K/40K Secondary 2 6 7 Primary 3 4 SH 8 Audio Dimensions (Inches) A 1.33 B 1.64 C 0.85 Max. D 0.20 E 1.30 F 0.141 G 0.344 H 0.156 CHASSIS MOUNT - HERMETICALLY SEALED AUDIO TRANSFORMERS * Deep-drawn steel case with tin plated finish, with two convenient 6-32 mounting studs with hardware. * Hermetically sealed for stable characteristics and long life. Header has nine 0.22" long solder pins. * Frequency response +/- 0.5 db max. from 50 Hz. to 15 Khz. * Insertion loss of apx. 1 db. * Maximum power level +15 dbm. (except 841, 842 & 844 which are +20 dbm) with specified characteristics, or higher levels with reduced low frequency performance. * Electrostatic shield between primary & secondary connected to terminal 9. * Humbucking construction * Balanced split windings on primary & secondary for circuit versatility. Primary may be used as a secondary and vice versa for impedance matching. * Overall dimensions 1.75" wide x 1.25" deep x 2.56" high max. * Shipping weight 0.5 lb. Guelph, Ontario (519) 822-2960 St. Laurent, Quebec (514) 343-9010 (c) Cheektowaga, NY (716) 630-7030 CANADA USA www.hammondmfg.com Basingstoke, UK 01256 812812 Queenstown, Australia 61-8-8240-2244 EUROPE 76 AUSTRALIA Broadcast Quality (800-850 Series) CHASSIS MOUNT - HERMETICALLY SEALED AUDIO TRANSFORMERS (continued) Part No. Application Nominal Impedance Primary *50/200 *50/200 (60/240) *125/500 (150/600) *7.5/30 *7.5/30 *50/200 *50/200 *125/500 (150/600) *125/500 (150/600) 5K/20K 5K/20K 10K/40K 5K/20K 5K/20K (6K/24K) 10K/40K (12K/48K) secondary Secondary 50/200 125/500 (150/600) 125/500 (150/600) 10K/40K 600/2400 10000/40000 600/2400 10K/40K (12K/48K) 600/2400 (720/2880) 20K/80K 10K/40K 10K/40K 50/200 125/500 (150/600) 125/500 (150/600) Max. Pri. D.C. Unbalanced ma 0.8 0.8 0.5 1.6 1.6 0.6 0.6 0.4 0.4 0 0 0 0 0 0 801 Isolating, Matching 802 Isolating, Matching 804 Isolating, Matching, Hybrid 806 Dynamic MIC or Voice Coil to Grid 807 Dynamic MIC or Voice Coil to Base 808 MIC or Mixer to Single or P.P. Grid 809 MIC to Mixer to Base 812 Line or 150 ohm MIC to 1 or 2 grids 813 Line or 150 ohm MIC to Base 832 Interstage (ratio 1:2) 834 Interstage (ratio 1:4) 835 Interstage (ratio 1:1) 841 ** P.P. Plates to Line 842 ** P.P. Plates to Line 844 ** P.P. Plates to Line NOTES: * Electrostatic shield between primary & Audio ** Single plate requires parallel feed. When operating at impedances below nominal, power capability is lower and the frequency spectrum is shifted downward, conversely, at higher impedances power capability and frequency spectrum will be shifted upward. CHASSIS MOUNT - HERMETICALLY SEALED AUDIO TRANSFORMERS * Deep-drawn steel case with tin plated finish, with two convenient 6-32 mounting studs with hardware (same as 800 series except low profile). * Hermetically sealed for stable characteristics and long life. Header has nine 0.22" long solder terminals. * Frequency response +/- 0.5 db max. from 20 Hz. to 20 Khz., except units over 5K ohms impedance, may be down 1 db @ 20 Khz. * Insertion loss of apx. 1 db. * Maximum power level +15 dbm. with specified characteristics, or higher levels with reduced low frequency performance. * Distortion is apx. 1.5% @ 20 Hz. under full power. * Electrostatic shield between primary & secondary connected to terminal 9. * Humbucking construction * Balanced split windings on primary & secondary for circuit versatility. Primary may be used as a secondary and vice versa for impedance matching. * Overall dimensions 1.7" x 1.2" x 1.65" high max. * Shipping weight 0.4 lb. Part No. 850C 850E 850G 850H 850J 850L 850N 850Q Application Emitter or MIC to Line Emitter or MIC to Line Line Isolation or Hybrid Line Isolation or Hybrid Output to Line, or Line to Base Output to Line, Matching or Bridging Output to Line, Matching or Interstage Interstage or Isolating Nominal Impedance Primary 12/48 50/200 150/600 150/600 150/600 5K/20K 150/600 10K/40K Secondary 150/600 150/600 150/600 300/1200 1200/4800 150/600 10K/40K 10K/40K Nominal Resistance +/- 20% Primary Secondary 6 70 27 68 71 71 70 140 69 570 2240 69 65 4980 4890 4980 Basingstoke, UK 01256 812812 Queenstown, Australia 61-8-8240-2244 EUROPE www.hammondmfg.com AUSTRALIA Guelph, Ontario (519) 822-2960 St. Laurent, Quebec (514) 343-9010 Cheektowaga, NY (716) 630-7030 CANADA USA 77 (c) |
Price & Availability of 850Q
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |